Automatic Technology Australia Elite Manual de instalación descargar pdf (Pagina 15)

AUTO-CLOSE MODE

Auto-close mode automatically closes the gate after a preset time

once the gate has reached its desired open position. The controller

starts to close the gate when the count down has expired. The

timer can be suspended by activating a suspending input (which

inputs 'suspend' depends on which auto-close mode is selected).

When the input is deactivated the auto-close timer is reset and the

count down recommenced. Auto-close functions are temporarily

disabled by certain actions. When this happens the controller will

not auto-close the gate until the user performs some action to

re-enable the function. Details about the three auto-close modes

follow.

STANDARD AUTO-CLOSE

This mode is selected by placing the mode selection switch

labeled “STANDARD AUTO-CLS” into the “ON” position.

When selected the gate will auto-close 30 seconds after being

fully opened. The following gives details about this auto-close

mode.

Auto-closes after being:

z Fully opened. (except when the gate is reversed to the open

position after a motor overload is detected while closing)

Countdown suspended by:

z The P.E. input being active.

z The OPN input being active.

Function temporarily disabled by:

z Activating the STP input while the gate is open.

z A motor overload causing the gate to reverse open.

Function re-enabled by:

z Activating the OPN input while the gate is open.

z Activating the OSC input, in SWIPE mode, while the gate is

open.

z By activating any input which cases the gate leaf to start to

close. The auto-close function will then be enabled once the

gate is re-opened.

The standard delay time of 30 seconds can be altered, see

STANDARD AUTO-CLOSE DELAY TIME, on page 16.

PEDESTRIAN ACCESS AUTO-CLOSE.

This mode is selected by placing the mode selection dip-switch

labeled “PEDESTRIAN AUTO-CLS” into the “ON” position.

When selected, the gate leaf will auto-close 15 seconds after

being opened for pedestrian access.

Auto-closes after being:

z Driven to the programmed pedestrian access position. (Except

when the gate leaf is reversed after a motor overload is

detected.) Reversing during pedestrian access is only

implemented when special PED modes are selected.

z Stopped by the P.E. input when closing after pedestrian access

(standard PED mode only).

Countdown suspended by:

z The P.E. input being active.

z The PED input being active.

Function temporarily disabled by:

z Activating the STP input while the gate leaf is in the

programmed pedestrian access position.

z Activating the STP input in condition 2 of 'Auto-closes

after being above.

z A motor overload causing the gate to reverse back to the

programmed pedestrian access position. (Reversing during

pedestrian access is only implemented when special PED

modes are selected.)

Function re-enabled by:

z Activating the PED input, in SWIPE mode, while the gate is in

the programmed pedestrian access position. Activating the

PED input and causing the gate leaf to start to close.

The standard delay time of 15 seconds can be altered, see section

PEDESTRIAN ACCESS AUTO-CLOSE DELAY TIME on page

16.

P.E TRIGGERED AUTO-CLOSE

This mode is selected by placing the mode selection dip-switch

labeled “P.E. TRIGGERED AUTO CLS” into the “ON” position.

When this auto-close mode is selected, the gate will auto-close

after the P.E. input has been activated and released since:

1. The gate was last closed

2. The P.E. triggered auto-close function

was re-enabled after being disabled.

3. The SWIPE input was activated.

Auto-closes after the P.E. input has been activated and then

released and the gate:

z Is fully opened. (except when the gate is reversed to the open

position after a motor overload is detected while closing).

z The gate has been stopped by the P.E. input.

Countdown suspended by:

z The P.E. input being active.

z The OPN input being active.

Function temporarily disabled by:

z Activating the STP input.

z A motor overload causing the gate to stop or reverse open.

Function re-enabled by:

z Activating the OPN input while the gate is open.

z Activating the SWIPE input.

z By activating any input which cases the gate to start to open or

close. The auto-close function will then be enabled once the

gate is re-opened or the P.E. input causes the gate to stop.

MODE SELECTION

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 23 24

Comentarios a estos manuales

Sin comentarios

Automatic Technology Australia Elite Manual de instalación Pagina 15

Comentarios a estos manuales